On/Off Control Tap Switch
On/Off Control Tap Switch
£20.50
Aston Cylinder
from £69.00
Aston Cylinder
The Aston Cylinder is available in 1/4pt and 1/2pt and with or without a self-contained water jacket (eliminates the possibility of cross-contamination). The cylinder comes with an Energised Non-Return Valve which prevents the beer from flowing back down the line....
from £69.00
Aston Cylinder Cabinet (pre 2017)
ASTON HAND PULL CABINET CYLINDER (pre 2017) The Aston Hand Pull Cabinet Cylinder is available as both 1/4pt and 1/2pt and with or without a self contained water jacket. The cylinder  comes with an energised non return valve. This prevents...
from £69.00
Replacement Seal Kit
  *Please note that these seal kits are not suitable for older style stainless-steel cylinders* Replace damaged or worn seals with our Seal Kit. Please note that this kit is only compatible with Harry Mason cylinders. All parts included are...
£15.80
Cylinder Clamps
We have 4 type of cylinder clamp available.  Please make sure you are selecting the correct one for your beer engine. Options Available 1/4pt for Clamp on & TTB                      ...
£15.00
Cylinder Top Cap
TOP CAP AND O RING Our Top Cap and O ring are compatible with all Harry Mason Cylinders and available in 1/4pt and 1/2pt versions.
£7.00
Cylinder Bottom Cap
The Bottom Cap comes complete with a non-return valve and is for use with Harry Mason 1/4pt and 1/2pt cylinders.
£15.00
Cylinder Inlet Kit
This cylinder inlet kit attaches to the bottom of the cylinder and consists of a wing burr, a rubber seal and a tail/inlet. Only suitable for the Aston beer engine. Comes with: Y thread open nut L/Y thread washer L/Y...
£1.80
Cylinder Clevis
This Harry Mason Clevis attaches the cylinder to the quadrant.
£1.50
Pint365 Cylinder Inlet and O Ring
This is a replacement inlet tail for the Pint365 cylinder, this comes complete with an O Ring connector
£5.83
Sold Out
Cabinet Cylinder Sling
The Cabinet Cylinder Sling links the quadrant hinge to the cylinder with the cabinet.
£22.00
Water Jacket Tails
This is a replacement Tail for a Harry Masons Water Jacket, you need to be a 100% certain that the all parts of the old tail are successfully removed
£1.50
Bucket Washer
from £2.00
Bucket Washer
Washer for bucket assembly inside cylinder
from £2.00
Inline Non Return Valve
Inline Non Return Valve
£12.50
Pint365 Eco-Cylinder & Outlet
Replacement Eco cylinder complete with outlet for PINT365 hand pull.
£69.95
Silicon Hose for Pump
This Silicon Tube connects the outlet on the cylinder to the swan neck tap
£5.00
Pivot Dog Point with Nut
This is where the cylinder mounts and pivots on the clamp on and through the bar frames Pack of 2
£4.00
Clevis Pin with E Circle
This Harry Mason Clevis Pin with E Circlip which is used to hold the cylinder clevis to the quadrant hinge.
£3.50
Pint365 Eco-Cylinder & Outlet (with water jacket)
Replacement Eco cylinder complete with an outlet and water jacket for PINT365 hand pull.
£69.95
Deluxe Plinth
Made as a spare for our hand pulls.
£35.00
Duckbill for Inline Non Return Valve
To be used with the Inline Non Return Valve
£2.60
Sold Out
1/4 Pint Bucket Assembly
Internal bucket assembly for the 1/4 pint cylinder 
£15.80
The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. Please click Accept Cookies to continue to use the site.
You have successfully subscribed!
ico-collapse
0
Recently Viewed
ic-cross-line-top
Top
ic-expand
ic-cross-line-top